Choosing the best location for your pool heat pump is crucial because it affects how well it will work and how long it will last. Next, in this article, we will share some vital pool heat pump installation tips to help you find the best placement for your pool heat pump and make the most of it.

Where Should A Pool Heat Pump Be Located?

A well-ventilated outdoor area is the best place to locate a pool heat pump. The optimum efficiency of a pool heat pump depends on good airflow. Therefore, we should install the pool heat pump outside so that the pool heat pump will have a good supply of fresh air for its operation and heat extraction. Try to install the pool heat pump as close to the pool, pool pump, and filter as possible, thus minimizing the pipe friction and maintaining a good water flux. The closer the pool heat pump is to the swimming pool, the more efficient it will be.

Listed below are the key things to remember when installing a pool heat pump:

• Choose a wide-open outdoor space that provides plenty of fresh air.
• Allow sufficient clearance on all sides of the pool heat pump for service, repairs, and cleanup.
• Keep the pool heat pump away from gutters, sprinklers, and other water sources. In particular, check that water is not running off the roof onto the unit. Otherwise, large amounts of rainwater and debris may enter the top of the pool heat pump with guttering and cause damage to the pool heat pump.
• No overhanging trees or eaves shall be blocking the exhaust air from the pool heat pump. Make sure to trim any nearby vegetation to prevent it from encroaching on the pool heat pump.

Should A Pool Heat Pump Be In The Sun?

You can install a pool heat pump in the sun, but that will not increase the efficiency. Since a pool heat pump relies on the air temperature around it rather than heat from the sun, it is even more critical to provide adequate airflow and water flow to the pool heat pump.

How Much Space Do You Need Around A Pool Heat Pump?

Pool heat pumps require sufficient air space around them. Otherwise, the compressor will overheat, and high-pressure protection will take place. In more severe cases, it will burn out the compressor and make the pool heat pump inoperable. Here are some installation space guidelines for TurboSilence® Full-inverter pool heat pumps from Fairland, so you can get a general idea of how much clearance requirements you need to install an inverter pool heat pump.

• To ensure good airflow, leave at least 500mm for the air inlet and a minimum of 700mm on either side of the pool heat pump.
• It is important to leave a well-ventilated space at the air outlet of the pool heat pump. Do not enclose it. Try to keep all obstacles out of it. Leave at least 1.5 meters of space is most appropriate.

Here are some photos of the completed installation of the TurboSilence® Full-inverter pool heat pumps for your reference.


By Summerwave Heat Pumps                                                          By Indemaj Water Treatment Co.

The INVERX Vertical (on the left) and INVERX Horizontal (on the right) from Fairland are two of the most popular TurboSilence® Full-inverter pool heat pump models. As long as you provide them with an outdoor space with good airflow when installed, the TurboSilence® Full-inverter pool heat pumps can deliver you 16 times energy saving and 15 times quieter swimming experience across the four seasons.

Do Pools Heat Up Faster With A Pump On or Off?

Actually, To heat water the pump must be turned on. But that's not all, Also faster water flow does not mean it will heat up more quickly because heat exchange also takes time. If you want to heat your pool faster, we recommend you increase the heating capacity of your pool heat pump. For example, you can switch on the Turbo Mode of X20, the latest model of Fairland’s TurboSilence® Full-inverter pool heat pumps. The upgraded high-performance inverter compressor allows you to turbo the heating capacity up to 120% in one touch, helping you heat your pool to the target temperature in less time.

Moreover, it will be a much wiser investment to opt for a larger capacity model, especially for inverter pool heat pumps. A larger model of inverter heat pump for swimming pool has a larger heating capacity. It can produce the same heat at a lower capacity and dramatically reduce energy consumption, making a substantial dent in your electricity bill. Also, a higher-capacity inverter pool heat pump can further lower its speed, thus creating a quieter swimming environment.

Final Words: What Is The Best Location For A Pool Heat Pump?

The best location for a pool heat pump is an outdoor area with access to circulating air. Additionally, the pool, pool pump, and filtration system should all be within easy reach of the pool heat pump. Knowing how much space you need to install a pool heat pump will help make your installation easier. Selecting a larger model of pool heat pump can effectively help heat your pool quickly. Contact Team Fairland, a pool heat pump factory, at sales@fairland.com.cn with your inquiry if you need assistance placing your pool heat pump or advice on choosing a larger model.